Last Chance ⌛ $12 Off Ends Midnight

Replaces the followung BSR needles:  ST-16,  ST-17,  ST-18, ST-19 AND SINGLE Tip ST-20, ST-21 Used in the following BSR cartridges:  SC5H, SC7M,  SC8H,  SC10H,  SC12H Speeds: All Tip Material: .0007 Diamond Tip; Radius: .003 Synthetic Sapphire

Read more less

Non-inductive dummy load resistors are a must for bench testing amplifiers. Also useful for testing loudspeakers and other audio circuits requiring an 8 ohm load. 5% tolerance. Dimensions: 6-1/2" L x 1-9/16" W x 3/4" H; Inner width of the screw holes: 5.4 mm; Inside edge to inside edge measurement between the two screw holes: ~144 mm.

Read more less

Standard mini headphones for home stereo or Walkman type use. Very inexpensive headphones makes for convenient back up or disposable use. Key Features Low cost headphones Comfortable lightweight design Great for Walkmans

Read more less

Simply drill 3/8" hole insert cutting head and compress handles. Gives you the ability to make square holes for fuse holders, special connectors displays etc. Material to be nibbled is placed in the gap between the punch and blade channel. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal. A scribe line can be followed by looking down on work in this position. A slot is cut by making successive cuts.

Read more less

Parts Express Steel Mesh 2-Piece Grill for 8" Speaker BlackConvenient and fast way to put grills on auto and PA equipment. 2-piece construction allows you to mount ring and woofer with one set of screws and snap the grill over the entire assembly. Installed screws are not visible. Screws and speed clips included. Heavy-duty expanded steel mesh design. Grill fits 8" speaker with a maximum outer diameter of 8-1/4". Overall diameter: 8-3/8". Sold individually.

Read more less

Finally! A foam gasketing tape designed specifically for loudspeakers! This specially designed foam tape is excellent for making an airtight seal around drivers, terminals, handles, horn lenses, or any other item that you're installing in a cabinet! Key Features Perfect for drivers, handles, horns, or anything that needs to be air-tight Ensures a good seal to enclosures Adhesive backed for easy installation

Read more less

L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 50 watts RMS, is designed to be used with 8 ohm loads, features a 3/8" shaft length, and comes with mounting hardware. Key Features Easy level adjustment without changing impedance Great for speaker design tweaking Maintains 8 ohm impedance Mounting hardware included

Read more less

Add a more stylish look to your turntable's S-shaped tonearm with this universal, gold plated contacts, aluminum headshell. Having two different cartridges and headshells makes your turntable more versatile.  Key Features Aluminum die-cast construction with integral finger lift 24 Karat gold-plated pre-installed lead wires For use with standard 2-screw magnetic cartridges Fits all "S" shaped tonearms with standard H-4 Bayonet Mount

Read more less

This fuse holder is perfect for 1-1/4" fuse lamps and normal fuses. The screws on each side make it easy to connect wires without crimping or soldering and the extended plastic reduces accidental shock. Key Features Screw terminals for easy hook-up Extended plastic on each side to prevent accidental shocks and short circuits Holds common 1-1/4" size fuses and fuse lamps Economical 5-pack

Read more less

Get that professional look with these black anodized hex head cap screws. The perfect mounting head for aluminum cast frame speakers. Large enough to secure the frame yet small enough to not deform paper and cork gaskets. Key Features 5/16" (8 mm) outer diameter head for holes in most medium size drivers

Read more less

Milled from solid brass, and 24-karat gold plated for maximum signal transfer, these locking, expanding, angled, and stackable, banana plugs feature a polycarbonate shell to provide protection from unintended contact while accepting up to 8 AWG wire. Key Features Locking pin separates the plug increasing retention force Stackable for use with bi-wired speakers Color-coded polycarbonate shells Dual hex screws for maximum cable retention 24 karat gold plated contact surfaces

Read more less

These connectors are designed with the audiophile in mind. 24 kt gold plating ensures the highest possible signal transfer and resists harsh environmental corrosion. These precision-machined connectors are made to last and last.

Read more less

Easy to use; compact and portable Simply plug your cables into the tester''s DVI-F and HDMI-F connectors Diagnoses the cause of color shift, sparkle, or missing picture Tester can be located at the source or display end of the system Displays the status of each HDMI signal component

Read more less

Pack of 10 6 mm entry size, 3.5 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables

Read more less

Pack of 10 10mm entry size, 4 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables

Read more less

Pack of 10 8 mm entry size, 3.2 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables

Read more less