What's New
E3D E3D V6 Socks Pro 3 pack
Genuine E3D Parts ONLY works for HotEnds which use the E3D V6 style heater block 3 Pack of original high temperature non-stick silicone socks for E3D V6 HotEnds These socks will keep your nozzle clean These socks really helps with sticky materials like Co-Polyesters and filled materials that like to build up on nozzles
$11.99
E3D E3D V6 All-Metal HotEnd Full Kit w/ Bowden Add-on 24v
E3D V6 all metal hotend 0.4mm nozzle for 1.75mm filament (with Bowden add-on) (24V). The E3D V6 has been redesigned from the ground up: smaller, easier and higher performance. Use up to 300C with the supplied thermistor for Polycarbonate, Nylon, PLA, ABS and more. Original E3D package. Assembly instruction available on E3D website.
$78.99
Dayton Audio Dayton Audio DCS165-4 6-1/2" Classic Subwoofer 4 Ohm
4-layer VC with polyimide former allows high power handling Vented pole piece and bumped back plate provide plenty of VC travel with minimal compression Copper pole piece cap minimizes inductance Rigid non-pressed treated paper/Kevlar cone with rubber surround Great for home and automotive applications
$70.99
Dayton Audio Dayton Audio DAEX25CT-4 Coin Type 25mm Exciter 10W 4 Ohm
Small size; just under 2" diameter, about 9/16" high Pre-applied 3M™ VHB™ adhesive for quick, durable installation Rare-earth neodymium motor and a proprietary voice coil 4-ohm impedance for use with small, Class D amplifiers 1" voice coil for 10 watt RMS power handling
$16.99
Dayton Audio Dayton Audio PC68-4 2-1/2" Full-Range Poly Cone Driver
Poly damped woven glass fiber cone controls cone break-up and provides a smooth roll-off High energy ferrite magnet increases BL for higher efficiency and increased output Rubber surround improves cone linearity and transients Smooth response with true full-range reproduction for simple speaker designs
$16.99
Dayton Audio Dayton Audio BPA-38G HD Binding Post Banana Jack Pair Gold
24kt. gold plating for best signal transfer and corrosion resistance 1-1/2" rear bolt mounts in speaker cabinets from 3/8" to 1" thick Large diameter knurled heads enable positive finger-tight connections Knurled shaft prevents post rotation
$14.49
Dayton Audio Dayton Audio DSS2-BC Black Chrome Speaker Spike Set 4 Pcs
Rigidly coupling a loudspeaker enclosure to a floor by means of a "spiking" system dramatically improves clarity, stereo imaging, and bass response. This is especially apparent with subwoofer systems. These attractive spikes are precision machined from solid brass and then plated with a durable finish. Barbed insert nuts and 6 mm threaded studs are included for mounting in cabinets with walls up to 1" thick. Set includes four cone spikes, four floor discs, four barbed insert nuts, and four threaded studs. Cone is 5/8", insert requires a 5/16" hole to be drilled prior to installation. • Dimensions: 9/16" diameter, 5/8" high (including disc).
$15.99
Parts Express Parts Express 8 Ohm 100W Non-Inductive Dummy Load Resistor
Non-inductive dummy load resistors are a must for bench testing amplifiers. Also useful for testing loudspeakers and other audio circuits requiring an 8 ohm load. 5% tolerance. Dimensions: 6-1/2" L x 1-9/16" W x 3/4" H; Inner width of the screw holes: 5.4 mm; Inside edge to inside edge measurement between the two screw holes: ~144 mm.
$20.99
Parts Express Parts Express Cable Pants 6mm 2-Conductor Black 10 pcs
Pack of 10 6 mm entry size, 3.5 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables
$10.49
Parts Express Parts Express Cable Pants 10mm 2-Conductor Black 10 pcs
Pack of 10 10mm entry size, 4 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables
$9.99
Parts Express Parts Express Cable Pants 8mm 2-Conductor Black 10 pcs
Pack of 10 8 mm entry size, 3.2 mm conductor size Ideal when building your own speaker cables Add a professional look to your customized cables
$10.99
Dayton Audio Dayton Audio iMM-6 Calibrated Measurement Microphone
Precision condenser microphone for critical measurement For use with any smartphone or tablet with a 3.5 mm TRRS headset jack True omnidirectional pattern with calibrated flat frequency response Headphone/Line Out pass-through jack for test signals or listening Kickstand feature elevates and angles device and microphone capsule
$26.19
Nuk3y Nuk3y Deadbolt Strike 1-1/8" x 2-3/4" with Dustbox
MATERIAL : Steel construction SIZE : 1-1/8" x 2-3/4" DUSTBOX is to be installed behind the strike plate to prevent dust from coming out of the latch hole. FINISH : available in stainless steel and matte black. NOTE : Screws are not included.
Pololu Pololu 2851 5V, 5A Step-Down Voltage Regulator D24V50F5
Input voltage: 4.5 V to 38 V for the version that outputs 3.3 V Fixed 3.3 V, 5 V, 6 V, 7.5 V, or 9 V output (depending on regulator version) with 4% accuracy Typical maximum continuous output current: 2.5 A Integrated reverse-voltage protection, over-current protection, over-temperature shutoff, and soft-start Typical efficiency of 85% to 95%, depending on input voltage and load; the switching frequency automatically changes at light loads to maintain high efficiencies
$48.99
Pololu Pololu 1350 Micro Maestro 6-Channel USB Servo Controller (Assembled)
The six-channel Micro Maestro raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting control. Whether you want high-performance servo control (0.25 μs resolution with built-in speed and acceleration control) or a general I/O controller (e.g. to interface with a sensor or ESC via your USB port), this tiny, versatile device will deliver.
$44.99
Pololu Pololu 1645 Force-Sensing Resistor: 1.5" Square
This force-sensing resistor (FSR) from Interlink Electronics is a passive component that exhibits a decrease in resistance when there is an increase in the force applied to the 1.5″ נ1.5″ (4 cm נ4 cm) active area With a force sensitivity range of a few grams to a few kilograms, this sensor is optimized for use in human touch control applications
$15.99
Pololu Pololu 1083 Universal Aluminum Mounting Hub for 6mm Shaft, #4-40 Holes
These universal mounting hubs are designed to work with most 6mm shafts, including round and 'D' shafts. Each hub has six mounting holes for 4-40 screws (not included), letting you mount custom wheels or mechanisms to your motors. 4-40 hex set screws (two included for each hub) allow secure coupling of shaft to hub. A 0.05' hex wrench (often the smallest size in SAE Allen wrench sets) is included for use with the set screws.
$13.90
Fastcap Fastcap Euro Door Stops with Screw (10 pack)
Makes your cabinets with inset doors look their bestSimply screw the Euro Door Stop inside your cabinet door and rotate to adjust until the faces are flush Made of soft noise absorbing EVA Camming action allows for fine adjustment Installs quickly and easily with one screw
Taylor Taylor R-0003-C Reagent #3 , 2 oz
Get the most accurate results possible Keep your pool water chemistry properly balanced It is recommended that you replace your reagents every year Available in 1 or 2 pack
$14.99 - $23.99
Nuk3y Nuk3y Thor Deadbolt
MODERN contemporary design will appeal to any light commercial and residential doors. 6-WAY twist action latch to fit all type of doors with 2-3/8 inch and 2-3/4 inch backset. This includes drive in, square, and round corner faceplate. EASY TO INSTALL with detail instruction included. ANSI/BHMA A156.2 certified to provide you high durability and meet building codes. KWIKSET keyway will be provided and keyed different. 2 keys per lock with 5 pin cylinder.
E3D E3D V6 Nozzle 1.75mm x 0.25mm
Genuine E3D V6 replacement nozzle for 1.75mm filament at .25mm nozzle size. This premium quality E3D replacement nozzle allows you to truly customize each and every print. This high quality nozzle have been created using community feedback and notes over multiple revisions from E3D.
$17.99
E3D E3D Hardened Steel Nozzle V6 1.75mm x 0.40mm
Hardened abrasion-resistant nozzles developed to last a lifetime. 3D printing with abrasives such as carbon fiber, glow-in-the-dark PLA or even filled filaments like woodfill all take their toll on a standard nozzle. These nozzles are fully integrated into the E3D Ecosystem and will fit V6, Lite6, and Titan Aero HotEnds, and are compatible with Prusa 3D printers.
$25.99
E3D E3D Nozzle X - V6 1.75mm x 0.40mm
Less build up, particularly of sticky and filled materials to the nozzle cone Improved first layer reliability; the slick coating has a reduced tendency to ‘drag’ material, particularly at sharp corners where tracks can peel up Easier nozzle cleaning, what little material that does adhere is easily wiped away with a paper towel leaving a very clean nozzle.
$40.99
E3D E3D V6 Extra Nozzle 1.75mm x 0.60mm
Genuine E3D V6 replacement nozzle for 1.75mm filament at .60 mm nozzle size. This premium quality E3D replacement nozzle allows you to truly customize each and every print. This high quality nozzle have been created using community feedback and notes over multiple revisions from E3D.
$13.99
You have seen 72 out of 597 products
Trending Products
$23.99
$76.99
$20.99
$22.99 - $29.99
$26.99$24.99
